GENERAL FEATURES :

• Suitable for non-aggressive liquids (water, light oil (2E) etc…), gaseous fluids (air, inter gases etc…)
• Working Temperature: ­­­­­­ ­‑10°C / 80°C
• Not suitable for use with dangerous fluids listed in group 1
• Minimum operating pressure differential 0,5 bar
• High reliability, quality, and performance; long life, corrosion resistance
• Wide pressure ratings, the range of flow rate and orifice options
• Ideal for the automatic control relevant 97/23/EC, Pressure Equipment Directive (PED) and 2006/95/EEC low voltage directive (LVD).
• COILS INTERCHANGEABLE
• FLOW FACTOR Kv of each valve is indicated so that the flow Q can be calculated as a function of pressure solenoid valves must be used with filtered fluids.
• The solenoid valve can be mounted in any position without affecting operation; vertical with coil upwards preferred.
• Standard pipe connection is G (BSP) (LSO 228-1) and on request; other pipe connections are available (NPT(ANSI 1_20_3)

  ELECTRICAL CHARACTERISTICS :  

Continuous Duty	:	ED % 100
Coil insulation class	:	H (180 °C)
Coil  Impergnation	:	Polyester Fiber Glass
Coil encapsulation Material	:	Fiber Glass reinforced
Ambient Temperature	:	from ­‑10°C ; 60°C
Protection Degree	:	IP 65 (EN 60529) with coil duly fitted with the plug connector
Electric plug connection	:	DIN 46340 3-Poles connectors (DIN 43650
Connector specification	:	ISO 4400 /EN 175301–803, from A, Spade plug (Cable Ø 6-8mm)
Electrical Safety	:	IEC 335
Standard voltages	:	For AC 12V,24V,48V,110V,230V For DC 12V,24V,48,110V
Other voltage n request;	:
Voltage Tolerances	:	For AC ­‑15%; 10% For DC ‑15%; 10%
Frequency	:	50Hz, other frequencies on request; (69 Hz)
On request; a connector with LED Specify coil voltage with an order

MATERIALS IN CONTACT WITH FLUID Body        : Brass Internal Parts : Stainless Steel and brass Sealing  : NBR Shading Ring : Copper Seats       : Brass Core Tube       : Stainless Steel Springs            : Stainless Steel On request; nickel plated body On request; sealing can be FPM (VITON),EPDM TECHNICAL FEATURES Max Viscosity : 5'E (-37cSt or mm2/s) Response Time: Opening Time : 400 ms to - 1600 ms, Closing Time:1000 ms to - 2000 ms Maximum Allowable Pressure : 25 bar Fluid Temperature for FPM (VITON) from-10°C; 160°C, for EPDM from-10; 140°C  

Valve Type / Order no	Connection Size	Orifice size	Pressure min	max	KV	Fluid Temperature		Seal	Weight
S1010	G	mm	bar	bar	It/min	. min	C max		(kg)
S 1 0 1 0 . 0 2	3/81	17.5	0.5	16	48	-10	80	NBR	0.68
S1010.03	1/7'	U.S	0.5	16	70	-10	80	NBR	171
S1010.04	3/4"	1/	0.5	16	85	-10	80	NBR	0.8
S 1 0 1 0 .0 5	1'	1/	0.5	16	90	-10	80	NBR	0.9/
S 1 0 1 0 .0 6	11/4'	46	0.5	12	390	-10	80	NBA	2.65
51 0 1 0 .0 7	11/7	46	15	12	460	-10	80	NBR	2.55
S 1 0 1 0 .0 8	2'	46	0.5	12	580	-10	80	NBR	2.98